Detailed explanation of noise suppression technology for LTE power supply equipment
Foreword
In recent years, with the diversification of wireless communication services such as online games and streaming media content, there has been an increase in requirements for high-speed data transmission and shortened waiting time. In addition, many users are pursuing an increase in the frequency efficiency of radio signal bandwidth in order to be able to perform efficient downloads at the same time.
However, the wireless communication methods (2G, 3G) have not yet fully met this requirement, and in order to solve the problems of "high-speed data transmission", "shortening of waiting time", and "effective frequency", LTE is used as a wireless communication method. Proposal, and began to be used by countries around the world.
On the other hand, due to the provision of a wireless communication terminal, the terminal noise degrades its own communication performance, and an EMC problem in the system (i.e., self-poisoning problem) occurs, and in order to maximize the performance of LTE, this problem must be solved.
Here, we will introduce noise countermeasures that affect the LTE communication specifications and how to select the necessary EMC countermeasure components through examples of noise countermeasures.
Investigate and resolve the "notes that affect the performance of LTE"
First, it is necessary to explain the necessary points of attention in noise investigation and countermeasures compared with general wireless communication methods.
The main points of attention are as follows.
The necessity of noise countermeasures in a wide frequency range
The first point is that when developing terminals for operators in different countries, a wide-bandwidth noise countermeasure is necessary. On the one hand, LTE uses a 700MHz bandwidth like Band13 or Band17, and also uses a bandwidth of 2.6GHz like Band7. It is expected that various frequency bands will be used in the future, and noise countermeasures used in wideband bands are necessary when developing LTE terminals that are common worldwide.
Necessity of noise countermeasures in MIMO (MulTIple-Input and MulTIple-Output)
The second point of attention is the use of an antenna approach called MIMO that uses multiple antennas. The wireless communication method hitherto has been to receive signals using one antenna, and the only one antenna can suppress deterioration of communication specifications by implementing noise countermeasures. However, MIMO utilizes more than two antennas, and it is necessary to receive multiple signals and implement noise countermeasures for all related antennas.
Introduction to noise countermeasures in LTE installation terminals
Next, we will introduce the actual noise investigation and solution examples. The LTE installed on the smartphone used in this example is Band13 (700MHz bandwidth).
Noise survey methods and results
The measurement method is shown in Figure 3. Cut off the wire inside the antenna and connect it to the coaxial cable on the side of the antenna. In addition, the coaxial cable is connected to the spectrum analyzer to determine the coupling noise of the antenna. (The noise is hereinafter referred to as "antenna reception noise")
The measurement results are shown in Fig. 4. The main antenna and the sub-antenna collectively couple the noise of a wide bandwidth. Therefore, this noise degrades the S/N of the received signal, thereby affecting the communication specifications.
Next, when investigating the noise source described above, as shown in FIG. 5, it can be seen that the noise of the data line of the flexible cable connected between the LCD screen and the main circuit board becomes large. In addition, to check whether the transmission noise and the wire reception noise are the same, it is necessary to ensure the same period as the noise shown in FIG. 5 when investigating the noise time variation. From the above results, it can be inferred that the data line of the LCD is a noise source that affects the communication specification.
MOSO Programmable LED Driver has programmable output current and constant power design. It is a brilliant design with advanced technologies. One Programmable driver can deliver different output currents and voltage at same power. It's easy for the fixture design and flexible for varies of outdoor application.
The Programmable Power Supply that operates in constant current model. Monitored by an infrared based programming device, the fully programmed drivers offer all dimming options (0-10V/PWM/Timing control/DALI) and a wide range of output current in a single driver, which deliver maximum flexibility with customized operating settings and intelligent control options for lighting manufacturers.
This Programmable LED Driver with varies of global safety certifications, including UL, CE, TUV, ENEC, CB, SAA, BIS, KC, etc compatible with the safety regulation for different countries.
The compact metal case and high efficiency enables the power supply to operating with high reliability, and extending product lifetime to at least 50,000 hours. Overall protection is provided against lightening surge, output over voltage, short circuit, and over temperature, to ensure low failure rate.
MOSO grants the product with 5 years global warranty. Customer can refer to Warranty policy, find the closest MOSO distributors or sales representatives, to get a local replacement in case of any failure.
Programmable LED Driver
Programmable LED Driver,DALI Programmable LED Driver,Programmable Dimmable LED Driver,Dimmable Programmable LED Driver
Moso Electronics , https://www.mosoleddriver.com