Analysis on the laying of weak electric cables for smart home in four steps

Nowadays, with the continuous development of information technology, many buildings and home-use devices tend to be smart. Therefore, we are using more and more weak cables. Among them are voice cables, network cables, cable TV cables, and audio cables. If you need to lay these weak electric cables for home decoration, what do we need to pay attention to?

First, designing the entire smart home wiring and wiring system requires a total control switch. The products of the Internet age and the information age are changing with each passing day. It is quite common for a family to have several telephones or multiple Internet access devices. In order to ensure the docking quality of various weak electric cables for the later maintenance management, a centralized control unit is designed for the telephone system and network cable in the home to control the entire home intelligent network.

During the laying process, we can select a certain place such as the entrance hall, the aisle, and the top of the study according to the location of the network cable. We design a small wire box (shaped like a power distribution box), and put all external incoming voice lines and networks. The cable and cable TV lines arrive at the cable box. At the same time, the telephone jack, network jack and cable TV jack of each room in the home must also reach the cable box. The cable can be connected in the online box according to the needs of the family. In order to ensure the signal quality, a TV signal multi-way branch adapter is needed in the online box. If multiple computers in the home are connected to the Internet, a network hub is required.

Second, the weak electric cable should be distinguished from the strong electric cable. The weak electricity information belongs to the low-voltage electric signal, and the anti-interference performance is relatively poor. Therefore, the weak electric cable should be routed away from the strong electric wire (that is, the power line used by the household). According to the relevant national regulations, the horizontal spacing between power lines and sockets, TV lines and sockets should not be less than 50 cm.

Third, the weak electric cable and its supporting equipment need to be mainly protected from moisture. The lower edge of the socket is suitable for about 30 cm from the ground. Because these weak cables are often routed under the roof or under the floor, a strong casing is required on the outside of these cables for moisture and replacement. Check the line for shorts before adding the bushing.

Fourth, in order to meet the needs of family development, it is necessary to reserve enough jacks. As time goes on, there will be more and more smart devices in the home, and more and more jacks will be needed. In the living room and bedroom, one or two telephone lines, network cables, and cable TV jacks should be reserved, and they should be distributed on different walls to facilitate the change of the position of the electrical appliances. The bathroom and kitchen can also be considered as needed to reserve a telephone jack. The restaurant can also consider whether to reserve a pre-TV cable jack for TV viewing during meals.

About Silicone Bottle Sleeve:

Bottles are widely used in our daily life ,like milk bottle ,water bottle ,etc . In the winner ,we need to store hot water in bottles ,while it's too hot to hold on hand ,at this condition ,we really need bottle sleeve to keep your hand from scalding ,while silicone bottle sleeve is popular all over the world ,it's very flexible to wear on the bottle to insulate,to get good feeling when hold the water bottle .

Silicone Bottle Sleeve description:

1.Product name:Silicone Bottle Sleeve,Glass Water Bottle With Silicone Sleeve, Water Bottle Sleeve , Silicone Glass Sleeve ,Water Bottle Silicone Sleeve,Glass Bottle With Silicone Sleeve

2.Place of origin:Guangdong China

3.Color:any pantone color

4.Logo:printing,debossed,embossed

5.MOQ:500pcs.

6.Package:1 pcs/opp,customized design is available.

7.Design:Customized

8.Certification:FDA,LFGB,SGS,ROHS,etc.

9.Usage:heat insulation

10.Silicone Bottle Sleeve photos for reference

Silicone Bottle Sleeve

Silicone Bottle Sleeve,Glass Water Bottle With Silicone Sleeve,Water Bottle Sleeve,Silicone Glass Sleeve,Water Bottle Silicone Sleeve,Glass Bottle With Silicone Sleeve

OK Silicone Gift Co., Ltd. , https://www.oemsiliconegift.com