Kai Yang Star for Micro-Fraction

In the past few years, I have said that I have used no less than 20 models of mouse. I started with the gaming mouse and I used the name of the famous purgatory viper. I feel it is amazing that ergonomics is the right thing to do. Classic products (like IE, no matter what)

Viper has been using for more than 2 years from the initial 1800 DPI Blu-ray to a 2013 Viper until 2 years ago do not know how to think that the Viper is large hand hidden disease? At that time on the next XX forum asking for help Do you have a similar answer to Kai Yang's one-round lap? You've got to answer Kai Yangxing (now discontinued 哎 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 遂 这 这 这 这 这 这 这 这In exchange for last resort with Kai Yang Xing

Because I take the mouse posture should be squeezing + pinching lead to similar to the G102 This is too flat raw raw This is the right side of the thumb sucking in no place to leveraging

By the way Tucao own LOL is only a gold but the demand is still quite a lot (I just do not have time to fight or it is at least a diamond to the suburbs that the king of the king).

Well, let's get into today's topic.

First, the hair dryer blows the hot air on the hair dryer (in fact, to save money, Hao is directly throwing new foot stickers).

89 This anion blowing hair feels similar to no negative ion.

Since only two screws are needed, there is no need to place the upper foot

The basic three-tool soldering iron soldering gun needed to change the micro-motion (removed by the micro-motion I'm tired of watching myself)

I don't have soldering links. There are usually soldering iron stores that sell.

At the time, I bought a soldering iron and other portable exercise board.

Several kinds of fee-based fretting (10M is on today's) D2F-F-3-7 The guy feels bare-handed feel best (looks like original) There is a chance to buy two toss and I have one more Open star

Separating the lid

Remove the upper and lower board cover is a board of a screw + buckle fixed to remove the screw board below the board is full buckle (personal feeling is convenient but still feel a bit fixed with a few screws)

Last change to the micro-motion Nissan gray point

This gray point stitch is a little bit S-type is also not the same as the general micro-movement pin behind the next micro-fight a little effort ~

After the last change, I went to the top cover but it had already been soldered. I couldn't polish the micro-movement directly with the main board. Then I could only polish the micro-motion button and see the new micro-movement with the polished gray point. I still feel smooth

After several crimson data lines, I was broken but I couldn't bear to re-weld the solder joints.

Traces of micro solder joints

The seller told me that it would be best to weld the solder joints one by one and then move it to the left and right, but after a few trials it felt like there was a residual solder that didn't get clean and then it couldn't come down and then you saw a teaching video directly in Youku (he There is a fixed tool I stuck directly with the drawer ~) Use tweezers to insert two holes in the front of the micro-motion and then the soldering iron directly touches the three solder points. The soldering iron moves back and forth across the three solder joints while the forceps are forced down or shaken back and forth. It's easy to go

But today due to the reason of the micro-movement pin, I was struggling not to mention the reasons for this micro-pin.

It takes a lot of hard work or it can't come down and it's going to make a big miracle.

Holes still have residual solder

Remove residual solder

Insert new fretting~

Do not rush to absorb the last lesson and try to feel it.

Feeling good welding ~

I couldn't do it myself.

After finishing the work energizing everything is normal (lights will give me heat off ~)

Saying that the K65 M's lamp is off or the old double-knife standard hasn’t been used

Finally, I said that on the video site, I wouldn’t be able to change the micro-teaching process. (Lacking and no mobile phone support)

To sum up, I am bold and diligent.

Hydrogen Pressure Sensor

Jiangmen Ever-smart Intelligent Control Instrument Co., LTD , https://www.fluhandy.com