Taiwan factory's production capacity continues to be full and the order visibility has reached Q4
After the LED chip factory went through the annual price-cutting and knockout competitions, it gradually stabilized this year. Due to the rapid increase of LED backlight penetration rate, LED TV penetration rate is expected to reach 70% this year, which is a significant increase from 40% to 45% last year. Let the LED TV deep-rooted Yuanyuan become the biggest beneficiary, especially the Yanyang Optoelectronics Co., Ltd., which is established in the joint venture between the mainland and LG. Under the strong demand of mainland and Korean TV customers, the production capacity has reached full load, and the LED lighting part With the increase of LED lighting applications, the shipment of LED LED lighting has also grown rapidly. The company estimates that the proportion of customers in mainland China this year is expected to double from last year, from 8% to 9% last year to 15%. While LED lighting is also in demand, the estimated revenue share will increase from 15% to 20% last year to 30%.
Looking forward to the second half of the year, Yuyuan said that due to strong customer demand, order visibility has reached the fourth quarter, and it is estimated that the third quarter of this year will be better than the second quarter. The company also plans to expand production in the fourth quarter of this year to respond. Market demand.
Dc Gear Motor can be defined as an extension of Dc Motor which already had its Insight details demystified here. A dc Gear Motor has a gear assembly attached to the motor. The speed of motor is counted in terms of rotations of the shaft per minute and is termed as RPM .The gear assembly helps in increasing the torque and reducing the speed. Using the correct combination of gears in a dc gear motor, its speed can be reduced to any desirable figure. This concept where gears reduce the speed of the vehicle but increase its torque is known as gear reduction.
Application field: usually used Electronic door locks, shutter motor, home audio equipment, sweep the floor machine robot
Features: dc gear motor drive precision, small volume, large torque, low noise, durability, low energy consumption, customized power design,easy installation, easy maintenance;Simplify design and save space.
Method of use: the best stable in horizontal plane, installed on the dc gear motor output shaft parts, cannot use a hammer to knock,knock prone to press into the dc gear motor drive, may cause damage to internal components, and cannot be used in the case of blocked.
Operating temperature range:
Dc geared motors should be used at a temperature of -10~60℃.
The figures stated in the catalog specifications are based on use at ordinary room temperature catalog specifications re based on use at ordinary room temperature (approximately20~25℃.
If a geared motor is used outside the prescribed temperature range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.Depending on the temperature conditions ,it may be possible to deal with them by changing the grease of the motor's parts.Please feel free to consult with us about this.
Storage temperature range:
Dc geared motors should be stored ta a temperature of -15~65℃.
In case of storage outside this range,the grease on the gearhead area will become unable to function normally and the motor will become unable to start.
Service life:
The longevity of dc gear motor is greatly affected by the load conditions , the mode of operation,the environment of use ,etc.Therefore,it is necessary to check the conditions under which the product will actually be used .The following conditions will have a negative effect on longevity.Please consult with us should any of them apply.â—Use with a load that exceeds the rated torque
â—Frequent starting
â—Momentary reversals of turning direction
â—Impact loads
â—Long-term continuous operation
â—Forced turning using the output shaft
â—Use in which the permitted overhang load or the permitted thrust load is exceeded
â—A pulse drive ,e.g.,a short break,counter electromotive force,PWM control
â—Use of a voltage that is nonstandard as regards the rated voltage
â—Use outside the prescribed temperature or relative-humidity range,or in a special environment.
â—Please consult with us about these or any other conditions of use that may apply,so that we can be sure that you select the most appropriate model.
when it come to volume production,we're a major player as well .each month,we rurn out 600000 units,all of which are compliant with the rohs directive.Have any questions or special needed, please contact us, we have the engineer group and best sales department to service to you Looking forward to your inquiry. Welcome to our factory.
Dc Gear Motor
Dc Gear Motor,Gear Box Motor,Gear Reduction Motor,Small Diameter Dc Gear Motor
Shenzhen Shunchang Motor Co., LTD. , https://www.scgearmotor.com